With any 1 GBit hardware the CPU usage should be negligible, nowadays. Recent laptops often come with Thunderbolt (>= 3) capable USB-C ports (sometimes not advertised because of missing/pending certification), such that looking for Thunderbolt Dock with an integrated (relatively) low-latency Ethernet port might be a good alternative in case you don't find a USB-C Ethernet dongle with suitable performance. It's possible that there are other USB-C Ethernet dongles that are lower latency and/or have higher quality drivers that are optimized for lower latency. (tests done under Linux Fedora 36 + 37, using the standard ping command with a count of 100 packets, each) TP-Link UE300C USB-C 1 GBit Ethernet dongle (ax88179_178a Linux driver): 1.9 ms average latency.Apollo Lake laptop with Lenovo Thunderbolt 3 Gen dock Ethernet port: 0.56 ms average latency.integrated Ethernet port (Dell Latitude E7270 from ~ 2016): 0.47 ms average latency.His answer did not work on windows 10.It depends on the exact USB-C Ethternet dongle.įor example, I've tested a few devices on a local 1 GBit LAN and a TP-Link UE300C 1 GBit USB-C dongle indeed showed the worst ping latency: Also if it is more than a 1-to-1 relationship the results could be unpredictable. I also used -eq instead of -match to ensure predictable results. In the case of USB, these solutions enable fanning out the local bus, providing flexibility towards additional downstream ports. However, what I am trying to target is the Connectivity status as shown in the Network sectionĮxpanding on answer, it is more efficient to call Get-NetConnectionProfile once and store the results. Ethernet bridge devices enable you to implement Ethernet connectivity to a host processor via USB, High-Speed Inter-Chip (HSIC), Peripheral Component Interconnect (PCI) or PCI Express ® (PCIe ®) interfaces. ResNet Students Connect your computers, printers, TVs, and other devices in Residence Halls and Campus Apartments. Wi-Fi Everyone at UB Learn about and quickly configure Wi-Fi available at UB for students, faculty, staff and visitors. 6 Up XX-XX-XX-XX-X.Įthernet 8 Remote NDIS based Internet Sharin.#10 4 Up XX-XX-XX-XX-X. Connecting to the Internet and UB's Networks Find detailed instructions on connecting to UB's networks. Get-NetAdapter -physical Name InterfaceDescription ifIndex Status MacAddressĮthernet 5 Remote NDIS based Internet Sharing.#6 26 Up XX-XX-XX-XX-X.Įthernet 11 Remote NDIS based Internet Sharing.#7 23 Up XX-XX-XX-XX-X.Įthernet 10 Remote NDIS based Internet Sharing.#8 54 Up XX-XX-XX-XX-X.Įthernet 12 Remote NDIS based Internet Sharing.#4 17 Up XX-XX-XX-XX-X.Įthernet 6 Remote NDIS based Internet Sharing.#5 15 Up XX-XX-XX-XX-X.Įthernet 4 Remote NDIS based Internet Sharing.#3 13 Up XX-XX-XX-XX-X.Įthernet 9 Remote NDIS based Internet Sharin.#11 12 Up XX-XX-XX-XX-X.Įthernet 3 Remote NDIS based Internet Sharing.#2 10 Up XX-XX-XX-XX-X.Įthernet 7 Remote NDIS based Internet Sharing.#9 7 Up XX-XX-XX-XX-X.Įthernet Intel(R) Ethernet Connection (2) I21. Note the Status for all of them is Up even if the Connectivity status shows "No network access". I am trying to find a Powershell command that will give me the Connectivity Status for all Network Adapters, for the ones where Connectivity equal "No network access" disable and re-enable the adapter.įirst I need to get the correct status, I have tried the following command but it only shows the physically connection.
0 Comments
Leave a Reply. |